General Services
In addition to our dyno tuning and mail-in ECU flashing, we also offer a full range of repair and maintenance services, including, but not limited to the following. [labor rate 120/hr]
Change oil and oil filter, replace spark plugs, check all fluids, inspect and clean air filter, lubricate cables and chain, synchronize carburetors/throttle body, check valve lash clearance, general inspection of unit.
Change oil and oil filter, replace spark plugs, check all fluids, inspect and clean air filter, lubricate cables and chain, synchronize carburetors/throttle body, general inspection of unit.
​
​
Piggyback Modules
​
​
Track Service Prep
​
​
ABS Delete/Install
​
​
Clutch Replacement
​
​
Tire Mount/Balance
​
​
Insurance Estimate
Change oil and oil filter, check all fluids, inspect and clean air filter, lubricate cables and chain, general inspection of unit.
Service
​
Basic Tune Up
​
​
​
Fork Rebuild
​
​
​
Dyno Pull
​
​
​
Piggyback Modules
​
​
​
Track Service Prep
​
​
​
Stretch Swingarm
​
​
​
Brake Lines
​
​
​
ABS Delete/Install
​
​
​
Exhaust Install
​
​
​
Engine Rebuild
​
​
​
Engine Swap
​
​
​
Clutch Replacement
​
​
​
Valve Check
​
​
​
Tire Mount/Balance
​
​
​
Chain/Sprocket
​
​
​
Insurance Estimate
​
​
Install DynoJet Power Commander or Bazzaz ZFI/FI management system. Includes dyno calibration, TPS, Gear, etc.
Change oil w/ filter with safety wire on oil drain/fill & filter, check and clean or replace air filter, service brake pads & calipers, bleed brake fluid, check battery & charging system, service drive chain, inspect steering stem/wheels & wheel bearings, inspect suspension movement.
Extend existing swingarm to desired length.
Install aftermarket, steel, carbon brake line kits.
Install ABS brake line system, or removal of ABS system and install brake line kit for racing, usually includes pump modification.
Installation of slip-on or full system exhaust.
Complete disassembly of engine, inspect, rebuild.
Removal and install of engine in chassis.
Replace clutch, slipper clutch/lockup's installation.
Inspect valve lash clearance.
Mount, balance, and install tires.
Remove and install front/rear sprockets and drive chain.
Change oil and oil filter, check all fluids, inspect and clean air filter, lubricate cables and chain, general inspection of unit.
​
​
Complete tear down of both forks to replace seals and oil
​
​
​
Run your bike on our Dyno to see its horsepower rating
​
shop rates do not apply to this service.
​
Install DynoJet Power Commander or Bazzaz ZFI/FI management system. Includes dyno calibration, TPS, Gear, etc.
​
​
Change oil w/ filter with safety wire on oil drain/fill & filter, check and clean or replace air filter, service brake pads & calipers, bleed brake fluid, check battery & charging system, service drive chain, inspect steering stem/wheels & wheel bearings, inspect suspension movement.
​
Extend existing swingarm to desired length.
Install aftermarket, steel, carbon brake line kits.
​
​
​
Install ABS brake line system, or removal of ABS system and install brake line kit for racing, usually includes pump modification.
​
​
Installation of slip-on or full system exhaust.
​
​
​
Complete disassembly of engine, inspect, rebuild.
​
​
​
Removal and install of engine in chassis.
​
​
​
Replace clutch, slipper clutch/lockup's installation.
​
​
​
Inspect valve lash clearance.
​
​
​
Mount, balance, and install tires.
​
​
​
Remove and install front/rear sprockets and drive chain.
​
​
​
We will provide an estimate which includes a breakdown of the cost of individual parts and labor.
​
​
​
We will provide an estimate which includes a breakdown of the cost of individual parts and labor.